Steam Crave Aromamizer Lite RTA Review

MTL from Steam Crave sounds weird. Initially, after seeing this tank, I had the full feeling that, of course, this is not MTL, well, this can not be, simply because it cannot.
Side airflow, a large area of ​​air holes, a huge steam line. Well, there is no such thing.
What was my surprise when I still launched Aromamizer light.

But, as always, let’s start with the box. This is the third tank this year sent to me from Steam Crave, and if the two previous ones were packaged in previous versions, then here, finally, we see the box that will go into series.

The box is made of rather thick cardboard with a magnet lid. The lid will contain the window through which the tank is visible, the color of the tank is marked on the side face, and the main characteristics are indicated on the reverse side.
Inside, the box is trimmed with red velvet and the tank itself lies on a red velvet bed.

On the “bed” there are also two glasses, a spare and pot-bellied spare, spare parts in the side pocket, a huge bundle of o-rings, I have a feeling that they were doubled, spare screws, there is even a reserve of 6 times. White spare screws of 4 hex and flat and 4 more hex black screws.
Screwdriver otchivaetsya from the usual T figure, it has both cross and flat and 6-sided slots. In general, the equipment is very, very.

Also included is the second drip, MTL’y.
In total, the tank is completed with two 510 driptypes:

And here again a strange thing, as with the whole tank. The one that cigarette turned out to be surprisingly not bad. Despite the rather strange form and sampling from the inside. At the bottom of the cigarette driptip has a hole of 6 mm, on top of 4 mm. Its height of the BS connector is 9 mm and a diameter of 10 mm.
The wide driptip has an inlet as well as 6 mm and an outlet ≈ 11 mm.

Complete instruction in English:

Characteristics:
Landing: 23 mm, width around the adjustment ring blowing 25 mm.
Height without connector and Drip type: 40 mm.
Weight: 60 gr.
Dimensions of complete glass: s
Outer diameter: 22 mm, for ordinary glass, for a wide glass 26 mm.
Internal diameter: 19 mm.
Height: normally 13 mm, but … I would say that the possible height of the glass is 12-14.5 mm.

Capacity with standard glass: 3.5 and potbelly, 4.5 ml.

The tank is currently offered in two colors, steel and black.

Focus On www.ave40.com For More Vape Tank.

Aromamizer is massive, but pretty squat. I do not understand the choice of a 23 mm diameter SteamCrave for landing, this was probably a kind of compromise, especially since the total width of the tank is 25 mm. The notches at the bottom and on the top hint at the European distribution of this tank, and it really does not look Chinese. However, such a design is typical for all Aromomizer. On the black version, in contrast to the steel one, the name of the tank is also perfectly readable, and, importantly for operation, indicating the blowing of the arrow.
The air intake is realized from two sides, but, the usual slots on the air intake ring are complemented by two pinhole holes. Moreover, since the adjustment ring adjusts the air intake into a rather wide opening in the base, the manufacturer had to make a large distance between the openings.

Let’s look at the overall design and parts of the tank:

Traditionally for Steam Crave, the base is inserted in the aromatizer from below, into the Chamber, in which all the “magic”, airflow, evaporation chamber and the beginning of the steam line are concentrated. On the “camera” is put on the air intake limiter, or the adjustment ring blowing. The body of the tank consists of a lower limiting ring, glass and a steam line with an upper refueling pad. The whole thing is completed, of course, with a lid and a drip tip.
Let’s start a more detailed discussion from above, with the body of the tank.

The openings of the gulf of liquid are quite ordinary, the lid is traditional, with a notch, only I did not like one. There is a notch on the lid, but not on the ring under it. When you take even the glass, when unscrewing the lid, the bachek is trying to figure it out, probably you need to twist it much tighter.
It is not customary that the lower part is more likely not part of the tank, it is not twisted with it, it is installed on top of the evaporation chamber. In general, the steam line is obtained consisting of two parts, on the thread, moreover, the length of the thread, which is in the upper part of the steam line, which is in the lower part, in the Chamber, is large enough.

Due to this, the height of the glass can vary, by as much as 2.5 mm, from 12 to 14.5 mm with a nominal height of 12.9 mm and it is nice, if anything, it will be easier to pick up the glass. Yes, and … 22 mm, so that glass can, as a last resort, be cut from a 20 ml plastic syringe. This is a definite plus 22 mm tanks.

In the photo you can see an interesting feature of the Aromamizer, most of the o-rings are internal, i.e. installed inside and not on the groove outside. The decision is very rare, o-rings will not be customary to change, but, in principle, nothing complicated.

Let’s reverse the tank and see what is on the reverse side.

The bottom cover covers the base and is, at the same time, the bottom of the “pool” into which liquid penetrates through the side openings in the chamber. This is a fluid-filled area.
The base is inserted into the center of the camera and through the grooves, it is practically filled in at the bottom with liquid. Cotton wool intake is carried out, almost as in RDTA, from such a micro tank below. The helix has side airflow through the perforated side holes. Blowing is obtained rather chiseled, thin air flows, but at the same time, wide, it goes beyond the limits of the spiral itself.
The evaporation chamber is very narrowed, its dimensions are 9 × 11.5 mm.

The base is drainless, which I categorically do not like, there are no special bore holes for the liquid there, so a small recess and holes. Vata is put, as I understand it, almost like on a drip, just to the bottom of the bath. Thrust it into the holes is not necessary, it should just lie on them.

Regarding the winding manufacturer in the instructions gives the following recommendations (in my retelling):
1. It is recommended to use a spiral with an inner diameter of 3 mm
2. Cut the legs of the spiral to 4.5 mm. When looking at the base under the coil should remain a small gap.
3. Use 12.5 mm cotton to clean the outer layers.
4. Do not unload the cotton, and fluff it, making it beautiful and fluffy.
5. Use the base o-ring as a guide for the length of the wool
. 6. Make sure you use all cotton to cover the holes for the base and other horizontal pieces.
7. Moisten cotton wool.
8. Install a spiral and cotton wool on the platform, place the tank body over the base and align the guides. Turn over the tank and unscrew. Attach the bottom of the base.

Honestly, I don’t know what kind of gap they had in mind, but with 4.5 mm legs it turns out something like the photo. I am totally upset that with such a spiral mounting system, it cannot be corrected. Generally, what … came up with “reckless” base.
It is noteworthy that the diameter of the helix is ​​recommended 3 mm, and not 2.5, as one would expect for MTL.
I installed a stainless steel fusion 2 × 3.2 + 0.1 … Actually, I put it in cigarette containers.
It is recommended to cut the cotton wool around the o-ring, of course, in a state where you fold the cotton down and not in its horizontal position. This can be seen in the picture accompanying the instructions.

Well, yes … It is advised to just throw cotton on the bottom of the base, not pushing anywhere, but covering the grooves and free space, which is practically not left there.

Conclusions:
Strange thing. According to the design and installation of the spiral, and indeed, the least from this tank can be expected MTL tightening. But at the minimum point blowing it is. It seemed that the steam density would not suffice, but the steam density is very good, the cotton is wetted just fine, the taste is significantly stronger than from the cigarette tanks I use, it is even overkill. It will be necessary to try all the same instead of a fusion monosil set.

Buck is elementary converted to DL. Just opened wider, added power and please. It does not interfere, of course, change the drip-type, but still, the pair turns out a lot.

Regarding the drip-type cigarette, I just don’t like it except the height. I do not like when the lips touch the tank. However, the cover is quite cold and it is not scary.

The tank is heavy. It leaves the feeling of a “real” European original. Great build, great fit parts. The blowing adjustment ring rotates smoothly and locks normally. The only thing that maybe the tank is a bit complicated for novik, but the taste just kills.

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available:  Steam Crave Aromamizer Lite RTA 23mm

Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Justfog Compact 14 Starter Kit

Rincoe Mechman Mesh Kit

Voopoo Drag Nano Kit

Voopoo Drag Baby Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

 

ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit Preview

As you know, the company Ultroner – by the way, a subsidiary of asmodus – has special feelings for Stabwood. Therefore, most, if not all, of their creations have such a finish. Today’s device also does not appear in the exceptions. 

ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
Dimensions: 70 x 24mm 
Weight: 68g Case 
Material: Stainless Steel + Stabwood 
Power: 1 x 18350 
Power Output:unknown 
Mode of operation: POWER 
Supported resistance: unknown 
Protection: low / high resistance, overheating, short circuit, wrong polarity 
Connector type: steel 510, pin gold-plated, spring-loaded 
Screen / diagonal: no 
Micro-USB port / charging: no 
Color: see photo below 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
Package contents 
– Mini Stick Mod 
– RDA 
– beauty ring at 22mm 
– beauty ring at 24mm 
– lanyard 
– spare parts 
– user manual 
– warranty card
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
Just a few words about the atomizer. I barely picked up the fashion info, while Dripke was completely silent. I will definitely supplement the article as the nuances appear, if it will only go in the set. Well, if it is offered separately, then we will allocate a separate article for it. I think there will be something to look at. While it is only known that it will probably be 24mm in diameter, and from myself I will add an assumption – this is a single-spiral. The captain is obvious, is not it?))) 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...

Focus On www.ave40.com For More Vape Kits.

With dimensions, not everything is clear, some sources talk about the figure of 22mm – the diameter, but I tend to 24mm. Naturally, this is just a tiny trubomod – even with a complete drip it risks lurking in the owner’s palm, without showing the nose out.
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
It looks quite decent, perhaps, so you can say about each creation of this manufacturer. For the decor, as always, in the answer inserts from stubwood. 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
From the start, only two versions of body coloring will be available, but stubwood will give the desired variety in design. 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
The connector was not shown to us, but they showed two complete beauty rings at 22 and at 24mm. 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
By the way, the bundle includes a cool lanyard with a medallion. Well, the ultroner would not be itself if it had not done something. 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
The fire button is small, made of ultem. In a compartment with dripka, designed in the same way, we get a good combination. 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
Naturally, our hero is controlled by a chipset, but so far I have not found any details about him. Access to the battery compartment through a screw cap at the bottom of the pipe module. 
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
Price $ 64.5
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...
ULTRONER Mini Stick Mechanical Mod + Ultroner RDA Kit - affordable beauty ...

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available :  Ultroner Mini Stick Mech Mod

Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Justfog Compact 14 Starter Kit

Rincoe Mechman Mesh Kit

Voopoo Drag Nano Kit

Voopoo Drag Baby Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Innokin Gala Review | Tap and Shake Pod System

The Innokin Gala is an open pod system and follows on from the huge hit that was the Innokin EQs pod mod.
innokin gala colour LED

 

Innokin have a superb track recornulld of beginner/mouth to lung vape kits, producing what was one of the best selling series in the vaping world, the latest in the series being the Innokin Endura T18ii.

So I have high hopes for the Gala kit.

What Can We Expect From The Gala Pod System by Innokin?

The Innokin Gala, as mentioned, is an open pod system so you can refill the pod with your own choice of e-liquid. So once you start to lose flavour and the coil reaches the end of its life, you chuck the whole pod.

It comes with the latest PLEX3D designed coils in a variety of colours and has an LED light bar that you can change to display a different colour when you take a vape. The change is made by tapping and shaking the device. Interesting. Let’s take a closer look.

The product was supplied for the purposes of this review by Innokin, thank you. As always my opinions are my own.

 

In the box

  • Innokin Gala Battery
  • 0.5Ω Pod (preinstalled)
  • 0.8Ω Pod
  • Pack of 3 E-liquid Bottle Tip Adapters
  • Lanyard
  • Warranty Card
  • Warranty Booklet
  • Tip Adapter Guide
  • Quick Start Guide
  • Battery Care Guide

innokin gala kit contents

Specs

  • Dimensions: 109mm x 25mm x 11mm
  • Weight: 50g
  • Tank Capacity: 2ml
  • Battery Capacity: 500mAh
  • Draw Activated
  • Tap and Shake to change LEDs

Design and Build Quality

The Innokin Gala comes in a number of different colours, I have the Saphire, and it has a nice stylised G logo and the word Gala in silver.Innokin Gala kit colours

Below that you have the light bar running down most of the battery (more on that in a moment).

Picking it up you immediately feel like it’s a nice piece of kit, just enough weight to feel quality without being heavy.gala by innokin in hand

It’s really discrete and fits nicely in the hand with the curved edges, despite having a shiny surface I never felt like I didn’t have a grip on it.

Controls and LEDs

There’s no buttons as it’s a draw activated device. The only control you have is over the LED light bar that is about 2mm wide and is about half the length of the complete kit.

This will light up when you put a pod in it and after you’ve taken a vape, to show you battery life.

Confusingly putting a pod in will show the battery one way (colour of flash) and after vaping it will use another (number of flashes). This is because you can set it to be any of the 7 colour options when you vape on it.

Focus On www.ave40.com For More Vape Kits

3 Taps

The instructions tell you that you need to tap the “G” logo 3x quickly to light up the LEDs with whatever colour is currently set, then if you shake the device it will cycle through your 7 different options Blue, Magenta, Red, Pink, Yellow, Aqua, Green and Off.

Then you either wait 4 seconds or take a puff on it to set the colour… Except that “Tap the device” doesn’t really describe what you need to do.

I spent a good 15 minutes touching the logo, tapping it, harder, softer, slower, quicker. Until eventually I just repeatedly ended up tapping away to get it to light up.

Turns out that it’s not a touch sensitive button, it doesn’t respond to the deformation of the plastic casing, or anything terribly sophisticated. It seems like it’s a simple accelerometer that is calibrated for short, sharp, shocks.

I actually found out the most reliable way of getting this to work, was holding the base of the device and flicking the device to hit my other hand fairly forcefully.

Similarly if you do this 5 times, you get “Light Show” mode, which cycles through the 7 colours continuously until you either perform the secret handshake again, or wait 30 minutes.

Not entirely sure that’s a great idea if you’re trying to prolong your battery life. Speaking of which!

Battery Life

After recently testing a device with a 1,000mAh battery that could give me two days with a good tail wind, I thought I’d happily get a day.

Unfortunately during my normal day I walked to work (15 minutes) vaped on my lunch break (45 minutes) and vaped on the walk home… or I would have done if it had managed to last my whole walk!

For me, this wasn’t an all day device and sadly the battery life didn’t impress with the device I tested.

Pods and Filling

You get two pods in the kit, the 0.5Ω pod is preinstalled, and you get a spare 0.8Ω.

I’m always pleased to see pod manufacturers include a spare, not enough do it so it’s great to see Innokin have listened to the wants of vapers here.

The other plus point is that you can easily tell them apart as the 0.8Ω coil has a bright green surround and the 0.5Ω is black.innokin gala replacement pods

On one side of pod is the silicon tab that you lift up to fill with a stopper that fits inside the fill pot.how to fill the innokin gala pod

This is without doubt the single worst experience I have had filling any tank or pod system.

Tip Adapters

The 3 tip adapters that you get in the box are there because there’s only a small diameter fill hole, and there is no secondary hole to release the air.innokin gala tip adapters

Coupled with the fact it’s quite a deep hole that your tip has to travel down, you quickly end up with an airlock and juice spilling over the top of the pod.

I feel like the tip adapters were included as an afterthought when they realised they’d made it impossible to fill.

They are supposed to fit onto the end of an e-liquid bottle and are very narrow so you put it down into the pod and it allows the air to escape around it.

Except they don’t fit tightly onto the bottle, so filling it up becomes a three handed job where you need to hold the pod, hold the the bottle, hold the tip adapter.

And the reason you need to hold the tip adapter is because if it you put it all the way into the pod, you end up drawing e-liquid back up, and because it doesn’t seal over the bottle, it just ends up spilling out the top of the adapter.

Similarly if you try to position it near the top of the tank, you run into the problem of the narrow but deep hole, and once again you form an airlock… and spill e-liquid all over the pod.

Lanyard

Innokin has some really nice photos of the pod kit in a leather pouch with lanyard.

However in the box you get a really basic lanyard with a small leather type loop that you put the device through. Then I guess you just have to hope it doesn’t fall out? As there’s no way of really tightening it on the device and nothing solid to attach it to.innokin gala lanyard

Also you need to avoid covering the airflow hole that’s on the side of the device. You can at least adjust the length of it.

How Does the Innokin Gala perform?

So after all of that, how does it vape?

Well, I’m pleased to say that the flavour is not bad at all.innokin gala colour LED

I tested both the 0.5Ω pod with the Plex3D Mesh coils and the 0.8Ω with the ceramic coils.

I used my standard 50/50 Berry Ice from Vape Simple at 9mg.

On both of these coils the flavour was pretty good and quite hard to tell the difference at first.

Not a great deal of vapour, which is normal for a device of this type, but a satisfying draw that feels similar to the cigarette.

I did find I was missing a bit of the throat hit that I’m used to from this e-juice, but that softness might suit people vaping 18mg e-liquid a little better.

Unfortunately on only the third day of using it I started to have problems.

The 0.5Ω coil leaked slightly inside the battery. Now this may well have been user error, but I’ve been careful pushing in the tab after filling, as well as cleaning the pod which became necessary due to the messy filling method.innokin gala leak

What’s more inexplicable is I started getting really bad dry hits from the 0.8Ω coil, and this is when it was full of 50/50 e-liquid.

This just should not happen and what I think might be going on is that the tiny air bubbles it produces were collecting near the wicking holes and stopping any fresh e-liquid from getting back into the coil.

Either that or the wicking material in this coil just isn’t up to people taking a few hits in quick succession.

I shook it about, let it rest, but the problem came back after only a few draws every time I tried again.

On both of the pods I also had to keep an eye on my air bubble. It would usually collect on one side so that as you vaped you were running the risk of having one side of the coil not being properly saturated as the air bubble gets bigger.

This was especially true as the two sides of the pod don’t level out their e-liquid levels easily at all.

Pros

  • Pretty good flavour
  • It looks nice
  • Well built, feels good in the hand
  • LEDs are kind of cool

Cons

  • Filling is a PAIN
  • Dry hits from one pod
  • Short battery life
  • Lanyard not the best

Final Review Verdict

So after my 0.5Ω coil gave out on me I persevered for a while on the 0.8Ω coil, but honestly it was just getting frustrating.

This is especially true as Innokin recommend you don’t vape it to less than a third full.

So with about 1.4ml of useable liquid, a pain to fill, and having to recharge all the time, I can’t see me picking the Innokin Gala pod up again now I’ve reviewed it.

With nice feel, the funky LED light, and the flavour it’s capable of, I was really hoping that it could become a good little shirt pocket pod kit for when I’m out and don’t want to take something more serious with me.

Unfortunately all of its downsides just overwhelm the positives.

Have you used the Innokin Gala Pod System? If so we would love to hear your thoughts in the comments below!

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available :  Innokin Gala Vape Pod System Kit 380mAh

Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Justfog Compact 14 Starter Kit

Rincoe Mechman Mesh Kit

Voopoo Drag Nano Kit

Voopoo Drag Baby Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk.

Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Teslacigs Citrine 24 tank Preview

Teslacigs is back in touch. And again they will present another novelty. Rather, the official presentation, as such, has not yet been, but I gathered a bit of information after all. By the way, after numerous presentations of new boxing mods, the manufacturer decided to take a short break and submit a modest non-service to the public. It is likely that its release is timed to another new product, which simply has not been shown to anyone yet. It is likely that this tank will be implemented in tandem with it in the future, because you will not be cleared up in particular sales in this segment.

Teslacigs Citrine 24 tank 
Teslacigs Citrine 24 tank - plastic non-service ...
Case material: plastic + stainless steel
Atomizer type: maintenance-free
Evaporators: 0.15 / 0.17Ω
Capacity:2 / 4ml
Diameter: 24mm
Height: 44.5mm with Drip type
Connector: 510, pin gold-plated
Weight: unknown
Color: see photo below
Teslacigs Citrine 24 tank - plastic non-service ...
Package contents (likely)
– Citrine 24 tank
– replaceable evaporators 2pcs T-X5 / T-X4 (0.15 / 0.17 Ω) (one preinstalled)
– user manual
– quality certificate

The exterior of the tank is rather unusual, and all because the developers decided to follow the newfangled trends and execute the hull almost entirely of transparent plastic. Probably, such a design for any public, because such decisions emerge here and there. It should also be borne in mind that the processing of such products costs the manufacturer several times cheaper than the usual metal construction.
Teslacigs Citrine 24 tank - plastic non-service ...
From the start, a lot of color options were suggested right away, which is understandable – the matter is much simpler with plastic.
Teslacigs Citrine 24 tank - plastic non-service ...

Focus On www.ave40.com For More Vape Tank.

Our hero refuels from above, however at first it is necessary to unscrew a plastic cover with risks. We decided not to show this, therefore I hope that the thread is not cut in plastic, otherwise it is a “pain” due to the relatively short service life.
Teslacigs Citrine 24 tank - plastic non-service ...
Capacity is not the greatest, but it is necessary to take into account the small size.
Teslacigs Citrine 24 tank - plastic non-service ...
Our guest eats two types of replaceable evaporators. Unfortunately, it is not clear on which types of coils they are executed.
Teslacigs Citrine 24 tank - plastic non-service ...
The adjustment of the blower is implemented by the standard for such a segment constructive – swivel ring with risks, it is also plastic. It is located at the base of the tank, there are two air intakes, they are slightly larger than the average size.
Teslacigs Citrine 24 tank - plastic non-service ...
Pin is gilded and pours enough.
Teslacigs Citrine 24 tank - plastic non-service ...
The price is currently unknown, on the shelves of the counters, non-services have not yet been announced.
Teslacigs Citrine 24 tank - plastic non-service ...

GeekVape

Shield by GeekVape – Overview

This year one of the most interesting devices was the Aegis boxing mod from GeekVape . The novelty became the first, truly protected box with several very important qualities – real security, good pay and an adequate price tag. The only thing that surprised me a little was why the company did not release a complete atomizer, because it is almost an obligatory norm for manufacturers of this level. And so, with a slight delay, Shield Tank appeared , about which I now want to talk.
Shield by GeekVape - baby on SMOK vaporizers for your Aegis
I want to start with the fact that I really liked Aegis , in many respects, precisely because of the interesting design. As far as I know, the model sells very well, so I’m not the only one who liked boxing. Therefore, onGeekVape lay the task to make an atomizer, which will not yield to cool fashion. Honestly, I bet on dripku, but GeekVape felt that the tank will be more interesting.
Shield by GeekVape - baby on SMOK vaporizers for your Aegis
I found the tank myself on the manufacturer’s website, where quite recently the renders have been published and Shield doesn’t look very soft on them. I was already prepared to scold the designers, but then I found real photos and my opinion changed a little. The tank itself is not the most original design and resembles a bunch of analogs, for example, Digiflavor ‘s Bucho . The only thing that saves a little is the “protection” of the tank, which gives it an interesting look. But this item is not included in the kit, so you have to spend 🙂

Dimensions :

Height – 38 mm.
Diameter – 24 mm.
Weight – 50 g

Shield by GeekVape - baby on SMOK vaporizers for your Aegis

Focus On www.ave40.com For More Vape Devices.

As I said above, I was pretty sure that they would make a drip for Aegis . As a result, they made an unattended tank, which doesn’t fit (in my understanding) with such a box. But if we ignore this, then we get a nice tank with standard features, as for its format. The truth is not without interesting features. So, engineers suggest using the following evaporators with a tank – IM1 – 0.4 ohm (40-60W); IM4 – 0.15 ohm (60-80W).
Shield by GeekVape - baby on SMOK vaporizers for your Aegis

The highlight is compatibility with SMOK TFV8 Big Baby / Baby vaporizers . Not a bad choice extension, right? I think thanks to this, the number of potential buyers should increase. Air spiral obtained through the system of the lower airflow. Everything is standard – two slots and an adjustment ring.
Shield by GeekVape - baby on SMOK vaporizers for your Aegis
I had some doubts about the normal capacity of the fluid reservoir, but GeekVape directly surprised me. Completely filled tank contains 4.5 ml. Holes for refueling are under the top cover, and in order to access them, you just need to press the “button”. From the side you can even see the pin on which the whole structure rests. I’d like to believe that everything was done with quality 🙂
Shield by GeekVape - baby on SMOK vaporizers for your Aegis

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available :Geekvape Frenzy Pod Starter Kit 950mAh

Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Justfog Compact 14 Starter Kit

Rincoe Mechman Mesh Kit

Voopoo Drag Nano Kit

Voopoo Drag Baby Kit

Hellvape Dead Rabbit RTA Review

One of the most notable drips presented lately was the Dead Rabbit from Hellvape & Heathen . Developed in collaboration with a well-known reviewer, a dripulka is still a success. The Solo version gained considerable popularity , and now it’s the turn of the tank – Dead Rabbit RTA .
Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!
I want to immediately note that the designers managed to make it so that the relationship of all devices in the line is noticeable even with the naked eye. Even if you do not take into account the corporate logo engraved on the dome, then some common features with the original Rabbit are noticeable. Even if I inspired all this to myself, then it’s impossible to argue with the fact that the tank turned out to be stylish. Cool corrugated rings, giving brutality and a lot of color options. Cool! The overall picture is complemented by colorful drip types, a couple of which I would definitely like to get myself into the collection.
Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!
Apparently, the manufacturer is very pleased with his line and does not burn with the desire to change anything drastically. Perhaps this whole “corporate style” attracts many, but it still cannot last for long. It is necessary to change something, or the interest of buyers can die out. Well, okay, these are all lyrics, and now let’s see what the novelty hides under the hood.
Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!
Removing the cover, the user will find the same system as in the first drip. At first glance, there is no change, and the second too. Available are two racks consisting of four blocks. It is easy to guess that the spirals are in an upright position. Someone can be pleased with the opportunity to use in the mode of one helix. For fixing meet the side screws. Judging by the available photos, not afraid of even the fattest coils 🙂
Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!
Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!Lately, I am less and less surprised at the upper airflow. So the hero of today’s blowing with his top slots did not cause any surprise. Air enters the spirals through channels in the inner part of the shaft. With the spaciousness of the tank, everything is simple. Included are two types of reservoirs – standard for 2 ml and blown glass for 4.5 ml. Holes for refueling are under the top cover and to gain access to them you need to unscrew the upper ring.
Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!Dead Rabbit RTA by Hellvape & Heathen is now a tank.  Everything is good!  Base in place!

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available : Hellvape Dead Rabbit RTA

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Review: Topside Dual Squonk Mod by Dovpo

Dovpo has released a Topside Dual Squonk Mod. Skvonker dispersed up to 200 watts, provided with a compartment for two batteries and completed with a pair of silicone bottles, refueling from above.

Dovpo announced in Instagram an Topside Dual Squonk Mod device  . The modified two-battery version of the previously released squonker was designed in the same style, but with more prominent sides. They did not make any changes to the control panel – the round fire button, the display and two adjustment keys remained in their original places. Behind the landing pad, in the recess, they placed the familiar rolled cap, which is responsible for filling the bottle. On the back wall cut a wide window. At the bottom lay a hinged cover

Maximum power ranges from 5 to 200 watts. In addition to the option, the varivolt, bypass and thermal control are supported. For powering, two 18650 batteries are required, charging goes up to 2A.

Silicone tank is located in a removable module with a magnetic lock, its volume is 10 ml. The minimum resistance is 0.08 ohms.

The package includes an additional tank, USB-cable, spare parts and instructions.

Main characteristics:

  • Size – 88.5 by 54 by 42 mm
  • Meals – 2х18650
  • Charging current up to 2A
  • Power from 5 to 200 watts
  • Resistance from 0.08 to 3.0 ohms
  • Tank capacity – 10 ml
  • Top dressing

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available :  Dovpo Topside Dual Squonk Box Mod

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

iJoy Captain PD270 Mod Reviewed – Are 20700 Batteries Really The Future?

Introduction – The Captain PD270 mod from iJoy

Vaping giant, iJoy, out of Shenzhen, is hellbent on innovating and, somehow, they just keep hitting the money and it looks as though that could be the case again with the iJoy Captain PD270 mod.iJoy Captain PD270 review

Having released the first dual 26650 mod, a result of their partnership with Limitless: the iJoy Limitless Lux, along with a string of impressive RDAs out of the same partnership.

More recently, the first quad 18650 device and brother of the Maxo Zenith, the iJoy Maxo…we’ve continued to be impressed.

Now, once again, iJoy have pushed the envelope, with the release of the Captain PD270 regulated TC mod.

A device that runs on dual 20700’s:  a whole new breed of battery being introduced to the vaping world by iJoy.

Given the fact that we may have reached the limits as far as low ohm-age on our sub-ohm devices goes, the two areas that could, of course, still use tweaking are those of batteries and chip-sets.

The Captain PD270 proudly boasts winners in both departments. With impressive power, extreme ramp time, super responsiveness and seriously enhanced battery life, iJoy are set to make waves!

What’s In The Box

  • 1 x iJoy Captain PD270 box mod
  • 1 x USB charger
  • 2 x 20700 iJoy 3000mAh batteries
  • 1 x Silicon dual 18650 adapter
  • 1 x warranty card
  • 1 x User Manual

Features

  • Dimensions: 101.8mm by 57.9mm by 31mm
  • Dual 20700 High-Amp Battery
  • Dual 18650 High-Amp Battery w/ Silicon Adapter
  • Output: 234W
  • Minimum Resistance: 0.06ohm
  • TC Range: 200-600F
  • Ni200 Nickel , Titanium, and Stainless Steel Compatibility
  • Vertical Display Layout
  • OLED Display
  • Large Square Firing Button
  • Adjustment Buttons Below Screen
  • Hinged Battery Door Cover
  • Short Circuit, Overcurrent, Overvoltage and Overcharge Protection
  • PTC Protective Circuits
  • MicroUSB Port
  • Spring-Loaded Stainless Steel 510 Connection

Build Quality & Design

The sturdy zinc alloy and carbon fibre frame of the iJoy Captain PD270, combined with the hefty weight of the fabulous dual 20700 batteries, amount to what I can only describe as a lethal weapon…if you threw it at anybody, that would be the end of them. It’s heavy.ijoy Captain PD270 mod and tank

On opening the neat box packaging, I was struck by the sexy frame and perfect, huge, square firing button.

 

The deep and solid 510 connection sits on an upper surface that is more than ample enough to fit a 30mm tank without any sign of overhang.

The design is a very simple rectangular cylinder with rounded corners, just big enough to house the hefty 20700’s inside.

The hinged battery door is thick and the hinges feel strong. The battery chamber is snug and the whole device feels compact, with no rattles whatsoever.

That’s not to say it’s not ergonomic, it fits perfectly in hand and plants your feet firmly on the ground with its weight.

I really do love the weight of it, when it’s in your hand, you know it’s there!

The stupendous, clicky firing button couldn’t be better placed and the screen display fits in all the details you could ask for.

Focus On www.ave40.com For More Vape Kits.

Accessories

I was delighted to discover that the dual 20700 batteries were generously included in the pack, not to mention the nifty, silicon 18650 adapter that will allow you to use the device with your old 18650s…not that you’ll necessarily want to.

How Does The Captain PD270 Box Mod Perform?

The IWEPAL chip is highly responsive and does it’s TC and regulating perfectly.

The device adjusts to and reads new atomizers accurately and instantly and I find the display and controls highly intuitive and comprehensive.

Puff counter, mode, battery levels, wattage, resistance and volts are all displayed and three clicks on fire will take you to the settings menu where you can into into TCR and mode settings, adjust screen time and reset your puffs.

The responsive up and down navigation buttons can also be used to alter the wattage when on the main the display.

I experienced an extremely fast ramp time and an all round brilliant vape throughout the wattage range and I love the fact that I can fit ANY of my tanks on it with no overhang!

It operates like a dream in the really high wattage range and the mode system, with user, soft, hard and normal settings is an easy and effective way to customize your vape for different moods.

I just want to add that I really love the fire button, its solid, reassuring and perfectly thumb sized!

How To Operate the Menu System

  • 5 clicks on fire switches the device on or off
  • Use the up down adjustment buttons below the screen to alter wattage or navigate the menu
  • Reach the menu with 3 clicks on fire
  • Some menus require you to use the fire button to navigate because you use the adjustment buttons to change figures, such as the TCR menu

How To Replace The 20700 Batteries

  • Open the hinged battery door by sliding it forward first and then opening
  • You’ll see small +- signs on the door, so you know which way to slide your batteries in

Battery Life

Well, there’s just no denying it, these batteries make all the difference.

I’m a heavy, high wattage vaper and it’s a pleasure to not have to charge every 6-8 hours.

Picture yourself vaping happily at 90 watts for a day and a half before really needing a charge.

The 20700’s are in between 18650’s and 26650’s, without the awkward thickness of the 26650’s.

I don’t have a lot of experience with 26650 devices but for me, dual 20700’s are all I can ask for and really take care of the nagging battery life issues I usually deal with every day, as a heavy vaper.

Also, the batteries fit in the standard Nitecore external chargers so you won’t have to worry about buying a special charger.

I found the on-board charge extremely fast.

What I Liked

I love the look and feel, the heavy weight and the carbon fibre finish.

Great, comprehensive screen display with easy controls.

Awesome that dual 20700’s are included (in the kit I received) thanks iJoy!

Excellent battery life. Marvelous, clicky buttons and super responsive.

A really powerful, satisfying vape.

What I Dislike

 

I can’t fault the device, as far as look, feel, functionality and power goes, it’s an absolute beast of a box mod!

Final Review Verdict

Well, not only have iJoy been extremely generous by including dual 20700’s with the Captain PD270…they’ve succeeded in creating yet another badass, high powered vape mod that looks, feels and vapes like a dream.

Maybe iJoy are right and 20700’s are the way of the future, they certainly make a big difference to me and now I wish all my devices used them.

This is a top notch device at a brilliant price.

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available : IJOY Captain PD270 New Kit

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Ring ignition: Rimfire RTA from Voopoo

Voopoo has released the Rimfire RTA tank. The device received an adjustment of the fluid supply, non-spill-over design and a bottomless base on two spirals.

Voopoo introduced the Rimfire RTA device on Instagram . Serviced tank made of stainless steel in four colors. Air intake holes with adjustment ring located on top. Immediately above him fixed removable topkap hiding a pair of wide filling holes. They crowned the construction with an 810-m epoxy resin drip tip. The dome was perforated with a pair of fluid holes and decorated with the name of the company.Inside the outer dome there is another one, which, when rotated, adjusts the fluid supply to the evaporation chamber. On the deck, there are four slots for fixing one or two spirals, eight holes for the bottom blower and two separate tanks for laying cotton wool. The winding legs are mounted on top and pressed with screws in the walls of the base. In addition to the bottom grille, the air flow enters the spirals from under the dome. The standard volume of 2 ml can be increased to 5 ml.

The package includes two spirals, a screwdriver, extra glass, a set of screws, oringi, cotton, and instructions.

Main characteristics:

  • Height – 46.3 mm
  • Diameter – 26 mm
  • Weight – 84 g
  • Volume – 2/5 ml
  • Adjustable fluid flow
  • Top dressing

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available :  VOOPOO Rimfire RTA

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Review boxing mod Joyetech eVic Primo Mini

Joyetech eVic Primo Mini  is a small 80 watt starting mode. It is equipped with one 18650 rechargeable battery with a fast charge function. The mod is combined with the new ProCore Aries atomizer, which is equipped with a easy-opening top lid and a convenient system for quickly filling up liquid. This set is suitable for novice vapers, as well as for fans of portable electronic cigarettes.

Appearance and size

The body of the box mod is made of aluminum, stainless steel and zinc alloy. On the sides there are black carbon inserts. The device is quite compact, comfortable in the hand.

The mod can be purchased in black, silver, red, yellow and blue colors.

On top there is a connector for the atomizer, which is designed for large devices with a diameter of 24-25 mm with a pin of 4-5.5 mm in depth. To attach the atomizer to the box mod 510 connector is used.

On the side is the device control panel. It has a screen, a large “Fire” button, “+” and “-” buttons, and a microUSB connector for charging.

Below are the holes for the withdrawal of gases and the battery cover.

Dimensions fashion  eVic Primo  mini:

  1. Height – 127.5 mm.
  2. Width – 39 mm.
  3. Thickness – 25 mm.
  4. Weight – 139 g.

Atomizer ProCore Aries is equipped with a 4 ml tank.

On top there is a plastic driptip in the form of a casing, which is tensioned onto the metal part with 3 sealing rings.

In the atomizer, the upper refueling function is implemented. To do this, you do not need to unscrew the top cover, just push it a little to one side and pull it up. The lid opens 2 large enough openings for refueling.

Atomizer fully understood. The glass of the tank is replaceable, so if it is damaged it can always be replaced with a new one. It is transparent, so the level of fluid in the tank is easy to control.

The evaporator is  screwed directly onto the base.

The blower is adjustable with a rotating metal ring. You can set as a tight cigarette, and light hookah tightening.

Atomizer size:

  1. Height – 52 mm.
  2. Diameter – 25 mm.
  3. Tank capacity – 4 ml.
  4. Weight – 70 g

Focus On www.ave40.com For More Vape Kits.

Equipment

eVic Primo Mini  is sold in this configuration:

  1. Boxmod itself – 1 pc.
  2. Atomizer ProCore Aries – 1 pc.
  3. Replaceable glass tank – 1 pc.
  4. Evaporator with a  resistance of 0.4 Ohm – 1 pc.
  5. Evaporator with a  resistance of 0.25 Ohm – 1 pc.
  6. Spare O-rings – 6 pcs.
  7. MicroUSB charging cable – 1 pc.
  8. Instructions – 2 pcs.
  9. Warranty – 2 pcs.
  10. Cardboard box – 1 pc.

Specifications

eVic Primo Mini  is equipped with 1 18650 battery and 80 W function board. The battery is charged with a current of 2 A. The outgoing current is 25 A.

The device works in various modes:

  1. Varivatt
  2. Bypass
  3. Start.
  4. Temperature control on nickel.
  5. Temperature control on titanium.
  6. Temperature control on stainless steel.
  7. TCR mode in 3 settings.

The minimum resistance of the device in the modes of varivatt, mehmod and start is from 0.1 to 3.5 ohms. In thermal control mode and TCR supported resistance from 0.05 to 1.5 ohms.

The mod has standard types of protection against the following problems:

  • short circuit;
  • low / high resistance;
  • low / high voltage;
  • battery recharge / recharge;
  • overheating;
  • work without an atomizer.

Main functions

The functionality of the Joyetech eVic Primo Mini boxing mod   is quite wide.

Varivatt – the main mode of soaring. In this mode, you can manually set the device power value. The maximum supported power value is 80 W, which is a good indicator for devices of this class. The minimum power is 1 W

Bypass activation activates the vape in the mech-mode. In this mode, the power of the device will directly depend on the battery charge level. The more charge there is, the more powerful the mod will be. On maintenance-free  evaporators  , this setting is undesirable.

Start mode is most suitable for beginners. When the start mode is on, the device will automatically adjust the power to the resistance value of the atomizer helix. The mod will memorize the last 10 power settings on various atomizers.

Thermal control modes on nickel, titanium and stainless steel are suitable for using  evaporators made from these materials. The range of temperatures available is + 100 … + 315 ° C or + 200 … + 600 ° F.

In TCR mode, you can pre-set the temperature settings for use in the mode selection menu. For this there are 3 memory slots.

The mod is equipped with a pre-heating function that allows you to determine the level of heating of the spiral after pressing the “Fire” button. This function is convenient to use when installed non-standard windings operating at high temperatures.

For optimal performance, it is better to use a liquid with an average concentration of glycerol (50-70%).

Using

The mod is controlled by the “Fire”, “+” and “-“ buttons. All the necessary information is displayed on the big screen. There are values ​​of power, resistance, temperature and battery charging.

The device turns on and off by pressing the “Fire” button five times.

By pressing the “Fire” button three times, the mode selection is activated. You can change them using the “+” and “-” buttons. First you select the mode you want. Then press the main “Fire” button to confirm the selection.

Pressing the “+” and “-” buttons simultaneously will lock the device. Thus, the buttons will not be pressed by themselves when the electronic cigarette is in a bag or pocket.

Pressing “Fire” and “-” activates the low power consumption mode (stealth mode). Simultaneous pressing of “Fire” and “+” will provide access to the preheat settings, as well as the appearance of the display menu.

The “+” and “-” buttons change the values ​​of power and temperature. If you hold one of them, quickly set the minimum or maximum value.

When hovering, the “Fire” button must be held down.

Advantages and disadvantages

This model has the following advantages:

  1. Compact size.
  2. Large selection of modes of operation.
  3. Powerful board.
  4. Replaceable battery.
  5. Convenient refueling technology.
  6. Stylish design.
  7. A large number of color options for fashion.
  8. Big screen.

However, it also has some minor drawbacks, for example, poor transmission of taste and lack of access to the  evaporator  when the tank is completely filled with liquid.

Primo Mini is the best combination of quality, functionality and price.

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available :  Joyetech eVic Primo Mini kit with ProCore Aries atomizer

Hot Sale Recommendation:

Dragon Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

Dovpo Topside Dual Squonk Box Mod

OUMIER WASP Nano RTA