Coil Master Genesis RDTA / Overview

The company Coil Master , already for a long time pleasing the steamers with their devices and accessories for wapping, decided to expand its assortment of atomizers, releasing RDTA under the not quite suitable, I think, for this type of device called Genesis. We will consider it in this review.

Packing and equipment

Comes Genesis RDTA in cardboard packing, painted in the company’s colors Coil to Master Master : black and red. On the front side of the package there is a name and a brief description of the features of the device. On the reverse side, we will see a bundle, specification and a label with the RDTA color marking. On one of the sides there is a scratch code for checking originality.

Focus On For More Vape Tank. - Free Image Hosting - Free Image Hosting - Free Image Hosting - Free Image Hosting - Free Image Hosting

Genesis RDTA has a standard package. Its complete list is presented in the table below.

Device Coil Master Genesis RDTA 1
Hex Wrench 1
Set of spare o-rings 1
Set of spare screws 1
Spare glass bulb 1
Pre-wound spirals 2
Organic Cotton 1
Instructions 1
Branded packaging 1 - Free Image Hosting

Appearance and parameters

Genesis RDTA is a classic bacodrip, externally and with a constructive almost no different from COMBO RDTA, manufactured by IJOY. The company Coil Master does not introduce non-standard technical and design solutions, but made it old-fashioned, but very high quality, however, for the quality I love the devices and sets from this company. Genesis RDTA has a lateral adjustable airflow, side fueling, massive bicycle racks, allowing to accommodate almost any “fantasy” of the co-builder. Bacodrip works only in the mode with two spirals. The device is made of 304 stainless steel. Genesis RDTA is available in two colors: steel and black. - Free Image Hosting - Free Image Hosting
Diameter 25 mm
Height 54 mm
Scope 6 ml
The weight 59 grams
Material Stainless steel 304, pyrex glass
Connector type 510

Design Features

Genesis RDTA , like any classic bacodrip, consists of a base with a 6 ml liquid tank, skirts, domes and drip-type located below. Drip-type non-standard, the landing diameter of 15 mm, is made of delirium, densely held on the dome with the help of two o-rings. The adjustment of the lateral blowing is realized by means of two cutouts on the lower part of the dome, which can simultaneously open / close the two airflow slots consisting of four holes located on the RDTA skirt, thereby adjusting the air supply to the spiral. At the same time, the dome itself is securely held by means of two O-rings. Inside the dome, a “flavor” spherical treatment is performed. The skirt is steel with two side airflow slots. It is held on the basis of RDTA using a large O-ring. - Free Image Hosting - Free Image Hosting

When considering the device base, no novelties, unfortunately, are not revealed: already become standard Velocity racks with rather large holes for fastening spirals. Moreover, it should be noted that the bases and the skirt with the dome from COMBO RDTA are fully compatible with Genesis. - Free Image Hosting - Free Image Hosting - Free Image Hosting - Free Image Hosting

On the back side of the RDTA is a gold-plated adjustable pin; certificates; information about the manufacturer and the name of the device. - Free Image Hosting - Free Image Hosting

No features in the installation of spirals and cotton packing, this atomizer did not present, everything is standard, as well as on dozens of other RDTA. The only thing I want to note is the horizontal axis of the spirals, located slightly above the blowing slots, which allows you to get a pseudo bottom blow and a small gain in taste. Whisking does not make sense to lower it to the very bottom of the tank, thereby reducing its volume (and it is just needed, because at a power of about 100W the liquid is melting in front of the eyes). - Free Image Hosting - Free Image Hosting


Unfortunately, I did not see anything extraordinary and innovative in the Genesis RDTA . The taste and dross on such devices will depend entirely on the spirals installed in them, so there is no sense in judging the “markers”, they are all different. Of nit-picking, I can produce too much skirt height with a dome, which increases the evaporation chamber, concealing the taste. A large O-ring, which holds the skirt on the base, is constantly jammed when refueling. But, in general, this device is not bad and fully works out the money invested in its purchase, especially since its cost in the online store of Coil Master company is only $ 30, which is quite good for the original device from the eminent manufacturer. - Free Image Hosting - Free Image Hosting

New from Coil Master

On the site of the company Coil Master you can pick up for yourself and purchase the necessary materials and devices for working with serviced atomizers. Let’s consider some of the novelties.

Coil Master Ready Box – a small set for serviced atomizers, consisting of 3 pairs of pre-wound spirals and twelve plates of high-quality Japanese cotton. Perfectly complement the camp kit Coil Master DIY Kit Mini .

Item SPEC. ID (mm) Material Res.
Fused Clapton 26 * 2 + 39AWG 3 NI80 0.3
Clapton Parallel 26 * 2 + 39 + 26AWG 3 NI80 0.3
Triple Clapton 26 * 3 + 40AWG 3 A1 + NI80 0.25 - Free Image Hosting - Free Image Hosting - Free Image Hosting - Free Image Hosting

Coil Master Skynet – a set of eight types of pre-engraved coils in the original plastic packaging. Each of the cells of the improvised “box” contains six ready-made spirals.

Item SPEC. ID (mm) Material Res.
Fused Clapton 26AWG * 2 + 39AWG 3 NI80 0.3 ± 0.05
Tortuosity 23AWG 3 NI80 0.22 ± 0.05
Clapton Parallel 26AWG * 2 + 39 + 26AWG 3 NI80 0.3 ± 0.05
Interlock Clapton (26 + 32AWG) + 24AWG 3 A1 + NI80 0.3 ± 0.05
Fused Clapton (TWIST) 28AWG * 2 + 32AWG 3 A1 0.45 ± 0.05
Flat Clapton 0.3 * 0.8MM + 32AWG 3 A1 0.45 ± 0.05
Clapton 26AWG + 32AWG 2.8. A1 0.6 ± 0.05
Super Tiger Coil 22AWG + 0.4 * 0.08MM 3 NI80 + A1 0.6 ± 0.05 - Free Image Hosting - Free Image Hosting - Free Image Hosting

Coil Master did not ignore the fans of the new-fashioned “toy” spinner, releasing a branded product – Spinner 1 . 
This spinner with the extension for the 510th connector can be mounted on the mechanical mode, after which you can screw up any of your atomizer from above. In my opinion, it turned out quite amusing “trinket”, but, I think, no one will consciously go on making contacts in the electrical circuit of Mehmod, introducing additional resistance, thereby reducing the effective power. - Free Image Hosting - Free Image Hosting

Leave a Reply

Your email address will not be published. Required fields are marked *